收藏本站
NCP1028
5.0 V/3.0 A Universal Mains Power Supply
Due to its low R DS(on) , the NCP1028 can be used in
universal mains SMPS up to 15 W of continuous power,
provided that the chip power dissipation is well under
control. That is to say that average power calculations and
measurements have been carried and correlated. The
design of an SMPS around a monolithic device does not
differ from that of a standard circuit using a controller and
a MOSFET. However, one needs to be aware of certain
characteristics specific of monolithic devices. Let us
follow the steps:
V in min = 120 Vdc
V in max = 375 Vdc
V out = 5.0 V
V out = 15 W
Operating mode is CCM
h = 0.8
1. The lateral MOSFET body-diode shall never be
forward biased, either during startup (because of a
large leakage inductance) or in normal operation
as shown by Figure 42. This condition sets the
maximum voltage that can be reflected during t off .
350
250
150
50.0
> 0 !!
-
50.0
1.004M
1.011M
1.018M
1.025M
1.032M
+ 110 + 18.3 or
Vin
5 ) 1
Vout ) Vf
d max +
+
+ 0.49
NVout ) Vin, min
(eq. 16)
1 ) NV
Figure 42. The reflected voltage shall always be greater
than the minimum input voltage to avoid the forward
biasing of the MOSFET body-diode.
As a result, the Flyback voltage which is reflected on the
drain at the switch opening cannot be larger than the input
voltage. When selecting components, you thus must adopt
a turn ratio which adheres to the following equation:
N(Vout ) Vf) t Vin, min t Vin min (eq. 14) . In our case,
since we operate from a 120 V DC rail while delivering
5.0 V, we can select a reflected voltage of 110 V
DC maximum: 120-110 > 0. Therefore, the turn ratio
Np:Ns must be smaller than
Np : Ns t 19 . We will see later on how it affects the
calculation.
2. Lateral MOSFETs have a poorly doped
body-diode which naturally limits their ability to
sustain the avalanche. A traditional RCD
clamping network shall thus be installed to
protect the MOSFET. In some low power
Figure 43. Primary Inductance Current
Evolution in CCM
turn ratio, V out the output voltage, V f the
secondary diode forward drop and finally, I peak
the maximum peak current. Worse case occurs
when the SMPS is very close to regulation, e.g.
the V out target is almost reached and I peak is still
pushed to the maximum. For this design, we have
selected our maximum voltage around 650 V (at
V in = 375 Vdc). This voltage is given by the RCD
clamp installed from the drain to the bulk
voltage. We will see how to calculate it later on.
3. Calculate the maximum operating duty-cycle for
this flyback converter operated in CCM:
NVout 1
Vin,min
out
4. To obtain the primary inductance, we have the
choice between two equations:
) Ipeak
(eq. 15) , where L f is the leakage
L + , where K +
and
applications, a simple capacitor can also be used
since Vdrain max + Vin ) N (Vout ) Vf)
Lf
Ctot
inductance, C tot the total capacitance at the drain
node (which is increased by the capacitor you
will wire between drain and source), N the Np:Ns
?
(Vind)2 D IL
(eq. 17)
fSWKPin I1
defines the amount of ripple we want in CCM
(see Figure 43).
Small K: deep CCM, implying a large primary
inductance, a low bandwidth and a large leakage
inductance.
http://onsemi.com
24
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
NCP1216AFORWGEVB BOARD EVAL NCP1216A 35W
NCP1351LEDGEVB EVAL BOARD FOR NCP1351LEDG
NCP3065BBGEVB BOARD EVAL NCP3065 MR16 BOOST
NCP3066SCBCKGEVB EVAL BOARD FOR NCP3066SCBCKG
NCP5005GEVB EVAL BOARD FOR NCP5005G
NCP5006EVB EVAL BOARD FOR NCP5006
NCP5030MTTXGEVB EVAL BOARD FOR NCP5030MTTXG
NCP5602EVB EVAL BOARD FOR NCP5602
相关代理商/技术参数
NCP1028P065G 功能描述:电流型 PWM 控制器 NCP1028 65 KHZ RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
NCP1028P100G 功能描述:电流型 PWM 控制器 NCP1028 100 KHZ RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
NCP1028PL065R2G 功能描述:交流/直流开关转换器 ANA 1 FREQ GULLWING RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel
NCP102MBGEVB 功能描述:电源管理IC开发工具 NCP102 4W MOTHERBRD EVB RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
NCP102SNT1G 功能描述:低压差稳压器 - LDO LDO LINR REG CONTRL RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
NCP1030 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Low Power PWM Controller with On-Chip Power Switch and Startup Circuits for 48V Telecom Systems
NCP1030_06 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:Low Power PWM Controller with On−Chip Power Switch and Startup Circuits for 48V Telecom Systems
NCP10301 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:AC-DC Offline Switching Controllers/Regulators